Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

精神活性物质在北京市某污水处理厂中的污染特征与生态风险

为了解污水处理厂对精神活性物质的去除特征及总出水对受纳水体的生态风险,采用固相萃取-高效液相色谱-串联质谱法调查了北京市某污水处理厂中13种精神活性物质的浓度水平与负荷量变化,并运用RQ（risk quotient,风险熵）对总出水中精神活性物质进行风险评估.结果表明:①13种精神活性物质在总进水与总出水中均能检出,总质量浓度平均值分别为2 395.10和63.59 ng/L,其中ρ（EPH）（EPH表示麻黄碱）占比分别为93.9%和67.9%,其次为COD（可待因）与METH（甲基苯丙胺）.污水处理厂上游地表水中ρ（EPH）、ρ（METH）与ρ（KET）（KET为氯胺酮）均高于总出水及其下游地表水,说明上游沿河可能有新的污染源输入.②污水处理厂对NK（去甲氯胺酮）、BE（苯甲酰爱康宁）和MTD（美沙酮）均呈负去除,其他精神活性物质的去除主要发生在二级生物处理与三级处理（超滤膜与UV消毒）阶段.③污水处理厂服务区域内精神活性物质的周内负荷量存在一定波动,AMP（苯丙胺）、METH、MDA（3,4-亚甲二氧基苯丙胺）、MDMA（3,4-亚甲二氧基甲基苯丙胺）、KET与HER（海洛因）的负荷量均在周末升高.④污水处理厂总出水中精神活性物质的生态风险均较低（RQ < 0.10）.研究显示,污水处理厂不能完全去除污水中的精神活性物质,总出水中残留精神活性物质对受纳河流生态系统产生的长期混合效应不容忽视.      

Analytical methods and environmental processes of nanoplastics

The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.     

基于最大熵模型的福建省红树林潜在适生区评估

本研究利用生物气候、地形、底质类型、海温等环境因子和红树林分布数据建立了福建省红树林分布模型,基于最大熵方法分析了福建省沿岸红树林潜在适生区的空间分布.根据模型输出结果对福建省红树林的生境适宜性进行了评估,识别了影响红树林分布的关键环境因子及其适生值区间,并通过空间叠加分析获取了福建省红树林保护与修复的优先区与空缺区域.结果表明,影响福建省红树林适生区分布格局的主要环境因子包括海表温度、气温和降水等,福建省红树林潜在适生区主要位于沙埕港-三沙湾-兴化湾沿岸、泉州湾-厦门湾-九龙江口沿岸、漳江口-东山湾沿岸等地,其中最优适生区面积约为91km².全省共识别出8处红树林保护与修复的优先区域,现存红树林保护率约为64.4%,保护修复空缺主要出现在沙埕港、三沙湾、罗源湾、福清湾等处,研究结论可为未来福建省红树林保护和修复行动提供科学参考.     

典型西南工业城市春冬季PM2.5来源与潜在源区分析——以柳州市为例

为了揭示柳州城区春冬季PM_2.5的来源及其潜在源区分布和贡献,利用2018年24h自动监测数据和气象数据对柳州市大气污染物浓度变化特征进行了分析,并且使用后向轨迹模型（HYSPLIT）对春冬季柳州市PM_2.5逐日72h气流后向轨迹和前向轨迹进行聚类分析,同时结合潜在源贡献因子分析法（WPSCF）和轨迹浓度权重法（WCWT）对其潜在源区和浓度贡献进行了分析.结果显示,（1）在研究期内,不利的主导风向和工业区布局导致研究区PM_2.5在春冬季污染较严重,且工业源和交通源是其主要本地来源;（2）春冬季PM_2.5高值主要来源于西北和东南方向,其中,西北向PM_2.5主要来源于本地排放,且浓度在空间上呈现西高东低的趋势;（3）春季后向轨迹PM_2.5浓度整体大于冬季,春冬季中对柳州市PM_2.5影响最大轨迹均来自东部的短距离输送,而来自西北的气流轨迹输对PM_2.5贡献最低.春冬季柳州市大气PM_2.5通过气流传输对贵州地区大气环境有较大影响;（4）春季,柳州市PM_2.5的主要潜在源区分布在广西东南部、广东中西部、南海沿岸海域、湖南中部、江西西北部、湖北东部及安徽西北部;冬季,主要分布在广西东南部、广东西南部和南海沿岸海域.     

含菌气溶胶扩散对人群的潜在影响风险

为分析生物气溶胶释放对人群潜在影响风险的情况,利用CALPUFF模型定量模拟了2019年7月24~8月20日中牧兰州生物药厂含菌气溶胶扩散、浓度空间分布、对人群潜在健康风险,并结合公开报道的检测数据开展验证.结果显示：生物药厂的含菌气溶胶排放源附近高值区主要集中于厂区四周,影响范围主要以厂区为中心,并向四周逐渐扩散;检测结果中兰州兽研所1#,兰州大学2#地区健康风险比例41.49：1,在模拟的相对风险大小的误差区间（36.15±8.48）范围内,说明本研究含菌气溶胶对人群潜在影响风险的模拟结果可信.     

中国乘用车塑料的动态物质流分析

结合行业信息并基于动态物质流模型,本文对1950~2050年间中国乘用车塑料流量与存量进行了历史测算与情景分析.历史测算表明：1950~2018年国内乘用车行业累计消耗了以聚丙烯（PP）、聚氨酯（PU）等为主的塑料3278万t,产生了337万t塑料废弃物;报废汽车拆解后的车用废塑料仅28%得到回收利用.针对未来情况,本文设计了乘用车保有量、单车塑料使用量两大关键因素下的不同情景组合.结果显示车用塑料存量及废塑料产生量将大幅增长,到2050年存量将达到0.7~2.7亿t,废塑料产生量将达到500~1600万t,汽车拆解和塑料再生等相关行业对此应充分关注.到2050年车用废塑料回收率若能提升至80%,将减少376万t/a的车用废塑料填埋或焚烧,显著减少环境风险.